Absolute Process Instruments APD 6380 D _ AC to DC transmitter-Fully isolated

Cecomp Electronics, APD 6380 D, AC to DC Isolated Signal Conditioner, 18 Output Ranges, 9-30 VDC, 10-32 VAC Power

Features:

One Minute Setup for Hundreds of I/O Ranges
External Switches & Tables for Range Selection
Zero and Span Output Calibration Potentiometers
Full 1200 V Input/Output/Power Isolation
Input and Output LoopTracker® LEDs
Output Test Button
Built-In Loop Power Supply for Sink/Source Output

Applications:

Convert, Boost, and Rescale Process Signals
Isolate Single-Ended (Common Ground) PLC Inputs
Interface Process Signals with Panel Meters, PLCs, Recorders, Data Acquisition, DCS, & SCADA Systems

The APD 6380 D accepts an AC voltage or current input and provides an optically isolated DC voltage or current output that is linearly related to the input.

Typical applications include signal isolation, conversion, boosting or a combination of the three. Full 3-way isolation (input, output, power) makes this module useful for ground loop elimination, common mode signal rejection or noise pickup reduction.

Sink/Source Output Versatility

For maximum versatility a milliamp output can be selectively wired for sinking or sourcing. This allows the APD 6380 D milliamp output to connect to a powered or unpowered current loop. The 20 VDC output loop supply can be used to power a passive mA device if required.

LoopTracker

API exclusive features include two LoopTracker LEDs (green for input, red for output) that vary in intensity with changes in the process input and output signals. These provide a quick visual picture of your process loop at all times and can greatly aid in saving time during initial startup and/or troubleshooting.

Output Test

An API exclusive feature includes the test button to provide a fixed output (independent of the input) when held depressed. The test output level is potentiometer adjustable from 0 to 100% of output span. The output test button greatly aids in saving time during initial startup and/or troubleshooting

Specifications Table:

Input	True RMS 0-40 mVAC to 0-300 VAC, 0-4 mAAC to 0-200 mAAC. Field configurablespecify range if factory is to set switches.
Output	0-1 V to 0-10 VDC, ±5 VDC, ±10 VDC, 0-2 mA to 20 mADC. Field configurablespecify range if factory is to set switches.
AC Input Range	Factory configured, please specify input range. Consult factory for special ranges Voltage: 0-40 mVAC to 0-300 VAC Current: 0-4 mAAC to 0-200 mAAC Measurements are true RMS
Input Impedance (Voltage Input)	Voltage (0-4 VAC): 1 MÎ© minimum Voltage (>4 VAC): 220 kÎ© minimum Current: 10 Î© typical
Input Frequency	40 Hz to 1000 Hz sinusoidal
Common Mode Rejection	120 dB minimum
DC Output Ranges	Field selectable ranges via switch settings VVoltage: 0-1 VDC to 0-10 VDC, 10 mA max Bipolar voltage: ±1 VDC to ±10 VDC Current: 0-2 mADC to 0-20 mADC, 20 V compliance, 1000 Î© at 20 mA Output offset: ±100% in 15% increments
Output Calibration	Multi-turn zero and span potentiometers (±15% of span adjustment range typical)
Output Loop Power Supply	20 VDC nominal, regulated, 25 mADC Max. ripple, less than 10 mVRMS May be selectively wired for sinking or sourcing mA output
Output Test	Front momentary button sets output to test level. Potentiometer adjustable 0-100% of span.
Output Ripple and Noise	Less than 10 mVRMS ripple and noise
Linearity	Better than ±0.1% of span
Ambient Temperature Range and Stability	10°C to +60°C operating ambient Better than ±0.02% of span per °C stability
Response Time	200 milliseconds nominal (0-90%)
Isolation	1200 VRMS minimum Full isolation: power to input, power to output, input to output
Housing	IP 40, requires installation in panel or enclosure For use in Pollution Degree 2 Environment Mount vertically to a 35 mm DIN rail
Connectors	Four 4-terminal removable connectors, 14 AWG max wire size
Power	9-30 VDC or 10-32 VAC 50/60 Hz, 2 W maximum

Write a Review