Absolute Process Instruments APD 6010 _ AC to DC transmitter up to 5 A input. Fully isolated.

Write a Review

Absolute Process Instruments

Absolute Process Instruments APD 6010 _ AC to DC transmitter up to 5 A input. Fully isolated.

Rating Required

Name Required

Email Required

Review Subject Required

Comments Required

$429.00

Absolute Process Instruments APD 6010 _ AC to DC transmitter up to 5 A input. Fully isolated.

Cecomp Electronics, APD 6010, A

Description
0 Reviews

Absolute Process Instruments APD 6010 _ AC to DC transmitter up to 5 A input. Fully isolated.

Cecomp Electronics, APD 6010, AC to DC Isolated Signal Conditioner, 85-265 VAC, 60-300 VDC Power

Features:

Full 1200 V Input/Output/Power Isolation
Zero and Span Output Calibration Potentiometers
Input and Output LoopTracker® LEDs
Functional Test Button with Remote Capability
Built-In Loop Power Supply for Sink/Source Output

Applications:

SConvert an AC Signal to a DC Process Signal
Monitor Voltage Ranges
Convert, Amplify Low Level AC Signals

The APD 6010 accepts an AC voltage or current input and provides an optically isolated DC voltage or current output that is linearly related to the input. Typical applications include monitoring line, power supply, shunt, and motor voltages or current (either directly or with a current transducer) for control, preventive maintenance, etc.

The full 3-way (input, output, power) isolation makes this module useful for ground loop elimination or noise pickup reduction. The APD 6010 is factory configured to customer requirements. Consult the factory for assistance with special ranges.

Sink/Source Output Versatility

For maximum versatility a milliamp output can be selectively wired for sinking or sourcing. This allows the APD 6010 milliamp output to connect to a powered or unpowered current loop. The 20 VDC output loop supply can be used to power a passive mA device if required.

LoopTracker

API exclusive features include two LoopTracker LEDs (green for input, red for output) that vary in intensity with changes in the process input and output signals. These provide a quick visual picture of your process loop at all times and can greatly aid in saving time during initial startup and/or troubleshooting.

Functional Test

An API exclusive feature includes the Functional Test Button to provide a fixed output (independent of the input) when held depressed. The test output level is potentiometer adjustable from 0 to 100% of output span.

The functional test button greatly aids in saving time during initial startup and/or troubleshooting. The functional test can also be enabled with a customersupplied external contact closure across terminals 5 and 6. This allows remote testing of the output or, for example, a PLC-controlled manual override setting

Specifications Table:

Input	True RMS 0-50 mVAC to 0-300 VAC, 0-1 mAAC to 0-1000 mAAC. Factory configuredspecify mVAC, VAC, or mAAC range.
Output	0-1 V to 0-10 VDC, ±5 VDC, ±10 VDC, 0-1 mA to 0-20 mADC, 4-20 mADC. Factory configuredspecify VDC or mADC range.
AC Input Range	Factory configured, please specify input range. Consult factory for special ranges Voltage: 0-50 mVAC to 0-300 VAC Current: 0-1 mAAC to 0-1000 mAAC Measurements are true RMS
Input Impedance (Voltage Input)	220 kÎ© minimum
Input Voltage Burden (Current Input)	1.0 VRMS maximum
Input Frequency	40 Hz to 1000 Hz sinusoidal
Input Protection, Common Mode	750 VDC or 750 VACp
Common Mode Rejection	120 dB minimum
DC Output Ranges	Factory configured, please specify input range. Consult factory for special ranges Voltage: 0-1 VDC to 0-10 VDC, 10 mA max Bipolar voltage: ±1 VDC to ±10 VDC Current: 0-1 mADC to 0-20 mADC 20 V compliance, 1000 Î© at 20 mA
Output Calibration	Multi-turn zero and span potentiometers (±15% of span adjustment range typical)
Output Loop Power Supply	20 VDC nominal, regulated, 25 mADC Max. ripple, less than 10 mVRMS May be selectively wired for sinking or sourcing mA output
Output Test/Override	Front momentary button or external contact closure sets output to test level. Potentiometer adjustable 0-100% of span.
Output Ripple and Noise	Less than 10 mVRMS at 40 Hz and above
Linearity	Better than ±0.1% of span
Ambient Temperature Range and Stability	10°C to +60°C operating ambient Better than ±0.02% of span per °C stability
Response Time	150 milliseconds nominal (0-90%)
Isolation	1200 VRMS minimum Full isolation: power to input, power to output, input to output
Housing	IP 40, requires installation in panel or enclosure For use in Pollution Degree 2 Environment Mount vertically to a 35 mm DIN rail
Connectors	Four 4-terminal removable connectors, 14 AWG max wire size
Power	85-265 VAC, 50/60 Hz or 60-300 VDC, 2 W maximum

Write a Review

Absolute Process Instruments APD 6010 _ AC to DC transmitter up to 5 A input. Fully isolated.

Write a Review

Absolute Process Instruments

Absolute Process Instruments APD 6010 _ AC to DC transmitter up to 5 A input. Fully isolated.

Absolute Process Instruments APD 6010 _ AC to DC transmitter up to 5 A input. Fully isolated.

Absolute Process Instruments APD 6010 _ AC to DC transmitter up to 5 A input. Fully isolated.

0 Reviews Hide Reviews Show Reviews

Absolute Process Instruments APD 6010 D _ AC to DC transmitter up to 5 A input. Fully isolated.

Absolute Process Instruments APD 6380 _ AC to DC transmitter. Fully isolated

Absolute Process Instruments APD 5393 _ AC to DC transmitter. Fully isolated.

Absolute Process Instruments APD 5393 D _ AC to DC transmitter. Fully isolated.

Absolute Process Instruments APD 6380 D _ AC to DC transmitter-Fully isolated