Absolute Process Instruments APD 5393 D _ AC to DC transmitter. Fully isolated.

Cecomp Electronics, APD 5393 D, IsoSplitter® Strain Gauge Amplifier/Signal Splitter 1 Strain Gauge Input to 2 Isolated DC Outputs, 9-30 VDC, 10-32 VAC Power

Features:

One Input to Two Outputs with Full Isolation
Zero and Span Output Calibration Potentiometers
Full 1200 V Input / Output / Power Isolation
Input and Output LoopTracker® LEDs
Output Test Button for Each Channel
Built-In Loop Power Supplies for Sink/Source I/O

Applications:

Split, Convert, Boost, and Rescale Process Signals
Split Process Signals for Control and Validation
Interface a Process Signal with Multiple Panel Meters, PLCs, Recorders, Data Acq., DCS, & SCADA Systems

The APD 5393 D IsoSplitter accepts a strain gauge, bridge, or load cell input and provides two optically isolated DC voltage or current outputs that are linearly related to the input. The input range and each output range are independent and can be specified as required. This provides an economical solution when one signal must be sent to two different devices.

Typical applications include isolation, output splitting, output device separation and redundancy (i.e. to prevent failure of the entire loop if one device fails), or a combination of these. The input signal is filtered, amplified, split, and then passed through an opto-coupler to the output stages. Full 4-way isolation (input, output 1, output 2, power) make this module useful for ground loop elimination, common mode signal rejection, and noise pickup reduction.

I / O Sink / Source Versatility

Standard on the APD 5393 D is an adjustable excitation supply for the input channel and 20 VDC loop excitation supplies for each output channel. The output power supplies can be selectively wired for sinking or sourcing allowing use with any combination of powered or unpowered milliamp I/O devices.

LoopTracker

API exclusive features include three LoopTracker LEDs (green for input, red for each output) that vary in intensity with changes in the process input and output signals. These provide a quick visual picture of your process loop at all times and can greatly aid in saving time during initial startup and troubleshooting.

Output Test

An API exclusive feature includes output test buttons for each channel to provide a fixed output (independent of the input) when held depressed. A test button is provide for each output channel. The output test greatly aids in saving time during initial startup and/or troubleshooting. The test output level for each channel is potentiometer adjustable from 0 to 100% of the output span. Terminals are provided to operate the test functions remotely for each channel. This also allows use as a remote manual override to provide a temporary fixed output if desired

Specifications Table:

Input	One 350 Î© Sensor, 1 mV to 2000 mV, 4-10 VDC Excitation, Factory Ranged
Output	0-1 V to 0-10 V, ±1 V to ±10 V, 0-1 mA to 20 mA, 4-20 mA, Factory Ranged
Bridge/Load Cell Input Range	Factory configured, please specify sensor mV/V and mV range Sensor range: minimum 0-1 mV to maximum 0-2000 mV Millivolt output range is determined by the sensitivity of the sensor (mV/V) and the excitation voltage applied. mV/V sensitivity X excitation voltage = total mV range
Input Impedance	1 MÎ© minimum
Input Protection, Common Mode	100 dB minimum
Excitation Voltage	Range: 4 to 10 VDC factory set, must specify Adjustment: ±10% via front potentiometer Maximum output: 10 VDC maximum at 30 mA Stability: ±0.01% per °C Designed for one 350 W (or greater) sensor
Channel 1 and Channel 2 DC Output Ranges	Factory configured, please specify for each output channel Voltage: 0-1 VDC to 0-10 VDC, 10 mA max up to 20 VDC with M19, M29, M39 Bipolar voltage: ±1 VDC to ±10 VDC Current: 0-1 mADC to 0-20 mADC, 4-20 mADC, 20 V compliance, 1000 Î© at 20 mA
Output Calibration	Multi-turn zero and span potentiometers for each output channel (±15% of span adjustment range typical)
Output Loop Power Supply	20 VDC nominal, regulated, 25 mADC for each output channel. May be selectively ordered for sinking mA output
Output Test/Override	Front momentary buttons or external contact closures for each channel to set output test levels. Each output test level potentiometer adjustable 0-100% of span
Output Ripple and Noise	Less than 10 mVRMS
Linearity	Better than ±0.1% of span
Ambient Temperature Range and Stability	10°C to +60°C operating ambient Better than ±0.02% of span per °C stability
Response Time	70 milliseconds nominal
Isolation	Full 4-way, 1200 VRMS minimum
Installation Environment	IP 40, requires installation in panel or enclosure with adequate ventilation For use in Pollution Degree 2 Environment Mount vertically (as shown in picture) to a 35 mm DIN rail allowing minimum 1" (25 mm) above and below housing vents for air circulation.
Connectors	Eight 4-terminal removable connectors, 14 AWG max wire size
Power	9-30 VDC or 10-32 VAC 50/60 Hz, 6 W maximum

Write a Review