OPTO 22 - SNAP-ODC5RFM _ SNAP 4-Ch Reed Relay Digital (Discrete) Output Module, Normally Open, Factory Mutual Approved

Write a Review

$76.28

Brand: OPTO 22
SKU:: SNAP-ODC5RFM
UPC:

OPTO 22 - SNAP-ODC5RFM _ SNAP 4-Ch Reed Relay Digital (Discrete) Output Module, Normally Open, Factory Mutual Approved

OPTO 22 - SNAP-ODC5RFM _ SNAP 4-Ch Reed Relay Digital (Discrete) Output M

Current Stock:

Quantity:

Adding to cart… The item has been added

Description
0 Reviews

OPTO 22 - SNAP-ODC5RFM _ SNAP 4-Ch Reed Relay Digital (Discrete) Output Module, Normally Open, Factory Mutual Approved

Quick Specs:

SNAP 4-Ch Reed Relay Digital (Discrete) Output Module
Normally Open
Factory Mutual Approved

The SNAP-ODC5R is a digital output module that uses low-voltage mechanical relays and does not provide optical isolation. Current rating depends on the voltage the module is used with. This module is normally open. The module includes a connector clamp to prevent sparks and is Factory Mutual (FM) approved.

Typical applications for these modules include analog signal and communication line multiplexing. Because of their low 10 VA rating, these modules are not recommended for inductive or capacitive loads (even very small loads) because the inrush current is likely to exceed the 10 VA rating.

IMPORTANT: Applications using 120 VAC are typically NOT suited to this module. If you are considering using this module for any application other than low-voltage purely resistive loads, see the detailed notes and rating curve in the data sheet, and call Pre-sales Engineering for specific guidance.

For many applications a better choice is the SNAP-OMR6-C module, which can handle a full 6 A at 0-250 VAC or 0-30 VDC.

If you do not need FM approval, see the SNAP-ODC5R.

Part of the SNAP PAC System, the module mounts on a SNAP PAC rack with a SNAP PAC brain or rack-mounted controller. Analog, digital, and serial I/O modules can all be on the same rack. Such an I/O unit is also well suited for PC-based control or for use as intelligent remote I/O for an Allen-Bradley Logix PLC system, such as ControlLogix, MicroLogix, or CompactLogix.

For easier, faster wiring, see SNAP TEX cables and breakout boards.

Build your system in the SNAP I/O Configurator.

Specifications:

	SNAP-ODC5RFM	SNAP-ODC5R5FM
Key Feature	Factory Mutual approved	Factory Mutual approved
Torque, hold-down screws	4 in-lb (0.45 N-m)	4 in-lb (0.45 N-m)
Torque, connector screws	5.26 in-lb (0.6 N-m)	5.26 in-lb (0.6 N-m)
Field Side Ratings (each channel)
Line Voltage - Range	0 - 100 VDC 0 - 130 VAC*	0 - 100 VDC 0 - 130 VAC*
Line Voltage - Nominal	--	--
Current Rating	0.5 amps switching*	0.5 amps switching*
Surge Current	0.5 amps*	0.5 amps*
Minimum Load	0 mA	0 mA
Output Voltage Drop	0 volts	0 volts
Off-state Leakage	0 mA	0 mA
Peak Blocking Voltage	100 VDC / 130 VAC	100 VDC / 130 VAC
Fuse (Common to all Channels)	Has four isolated channels. User must provide own fusing.	Has four isolated channels. User must provide own fusing.
Logic Side Ratings
Pickup Voltage	4 V @ 5.5 mA	4 V @ 5.5 mA
Dropout Voltage	1 VDC	1 VDC
Control Resistance	220 ohms	220 ohms
Logic Supply Voltage	5 VDC ± 0.25 VDC	5 VDC ± 0.25 VDC
Logic Supply Current	50 mA maximum	50 mA maximum
Module Ratings
Number of Channels Per Module	4	4
Turn-on Time	500 usec	500 usec
Turn-off Time	500 usec	500 usec
Isolation (Field Side to Logic Side)	1,500 volts (transient)	1,500 volts (transient)
Mechanical Life	200,000,000 cycles	200,000,000 cycles
Temperature	-20 to 70 °C, operating -30 to 85 °C, storage	-20 to 70 °C, operating -30 to 85 °C, storage
Agency Approvals	CE, FM, RoHS, DFARS; UKCA	CE, FM, RoHS, DFARS;UKCA
Warranty	30 months or mechanical life, whichever comes first	30 months or mechanical life, whichever comes first
* The current of the dry contact module must not exceed 10 VA power rating under steady state or momentary in-rush conditions. For voltages at or below 20 volts, the current limit is 0.5 amps. For voltages above 20 volts, the maximum allowable current is determined by the following equation: Current Maximum = 10 VA / Voltage. Rating curve is in the data sheet.

Write a Review