OPTO 22 - SNAP-AOD-29-HFi _ SNAP Isolated 2-Ch Analog TPO or PWM Output, 2.5 to 24 VDC, 0 to 100 kHz
Write a Review
OPTO 22
OPTO 22 - SNAP-AOD-29-HFi _ SNAP Isolated 2-Ch Analog TPO or PWM Output, 2.5 to 24 VDC, 0 to 100 kHz
- Brand
- OPTO 22
- SKU:
- SNAP-AOD-29-HFi
OPTO 22 - SNAP-AOD-29-HFi _ SNAP Isolated 2-Ch Analog TPO or PWM Output, 2.5 to 24 VDC, 0 to 100 kHz
OPTO 22 - SNAP-AOD-29-HFi _ SNAP Isolated 2-Ch Analog TPO or PWM Output, 2.5 to 24 VDC, 0 to 100 kHzQuick Specs:
- SNAP Isolated 2-Ch Analog TPO or PWM Output
- 2.5 to 24 VDC
- 0 to 100 kHz
The two channels are optically isolated from each other. Five volts through a 200 Ohm pull-up resistor are provided internally for each channel for use with TTL loads. This feature means you don't have to provide the pull-up voltage supply required for each output.
The SNAP-AOD-29-HFi mounts on a SNAP PAC rack and works with all SNAP PAC rack-mounted controllers and brains with SNAP PAC firmware version 9.3c or higher.
If your application doesn't require high-speed output, see the SNAP-AOD-29.
NOTE: If you are using a SNAP PAC IO4AB system to communicate with an Allen-Bradley PLC, you don't need this module. Instead, use the built-in TPO functionality available on all SNAP-PAC brains that support IO4AB.
Specifications:
| Switched Output | 2.5 to 24 VDC at 100 mA supplied externally |
| Maximum Survivable Switch Voltage | 60 VDC |
| Peak Current | 1.0 A (t < 10 milliseconds) |
| Period Range | 0.00001 sec to 64.25 sec |
| Percent Range | 0-100% |
| Period Resolution | 20.8 nanoseconds |
| Percent Resolution | 0.024% (12-bit) |
| Period Accuracy | +- 0.005% of period |
| Pull-up Voltage | 4.5 to 5.0 VDC |
| Pull-up Resistor | 200 Ohm |
| Minimum Output Pulse Width | 1 microsecond |
| Maximum Operating Common Mode Voltage | 250 V Continuous |
| Isolation: Channel to Channel | 250V Continuous |
| Power Consumption | 1.5 W (300 mA @ 5 V) |
| Ambient Temperature: | -20 °C to 70 °C |
| Humidity | 5-95%, non-condensing |
| Torque, hold-down screws | 4 in-lb (0.45 N-m) |
| Torque, connector screws | 5.26 in-lb (0.6 N-m) |
| Wire size range | 22 to 14 AWG |
| Agency Approvals | CE, RoHS, DFARS; UKCA |
| Warranty | Lifetime |
0 Reviews Hide Reviews Show Reviews
OPTO 22
OPTO 22 - SNAP-AIRATE-HFi _ SNAP Isolated 2-Ch Analog Frequency Input, 2 Hz to 500 kHz or 20 Hz to 500 kHz
OPTO 22
OPTO 22 - SNAP-AOD-29 _ SNAP 2-Ch 5-60 VDC Time-Proportional Digital Output Module
OPTO 22
OPTO 22 - SNAP-AOV-25 _ SNAP 2-Ch 0-10 VDC Analog Voltage Output Module
OPTO 22
OPTO 22 - SNAP-AIARMS-i _ SNAP Isolated 2-Ch 0-10 amp RMS Analog Input Module
OPTO 22