OPTO 22 - E1 _ 16-channel Digital Optomux Brain Board for Serial and Ethernet Networks

Write a Review

OPTO 22

OPTO 22 - E1 _ 16-channel Digital Optomux Brain Board for Serial and Ethernet Networks

Rating Required

Name Required

Email Required

Review Subject Required

Comments Required

$447.00

Brand

OPTO 22

SKU:

Description
0 Reviews

OPTO 22 - E1 _ 16-channel Digital Optomux Brain Board for Serial and Ethernet Networks

Quick Specs:

16-channel Digital Optomux Brain Board for Serial and Ethernet Networks

The E1 brain board is an Ethernet-ready I/O and communication processor for digital I/O systems. Designed as a drop-in replacement for Opto 22's serial-based B1 brain board, the E1 supports both serial and Ethernet networking and multiple simultaneous protocols. The Optomux protocol is available over both serial and Ethernet; in addition, OptoMMP and Modbus/TCP are available over Ethernet.

The E1 is designed for customers needing to upgrade existing Optomux systems to use Ethernet networking while preserving existing I/O racks, modules, and field wiring.

For Optomux applications over serial or Ethernet, use this software developer toolkit with the E1 brain: Optomux Protocol drivers and utilities.

For OptoMMP applications over Ethernet using Windows 7 (32 & 64 bit), use the .NET OptoMMP Development Kit for SNAP PAC.

Compatible I/O and mounting racks:

G4 digital I/O: G4PB8H, G4PB16H, G4PB16HC
Integral G4 I/O: G4PB16J, G4PB16K, G4PB16L
G1 digital I/O: PB4H, PB8H, PB16H, PB16HC
Integral G1 I/O: PB16J, PB16K, PB16L
Quad Pak I/O: PB16HQ

Set or read your B2 or E2 jumpers quickly using these configurators:

Specifications:

Power Requirements	5.0 - 5.2 VDC @ 0.5 amps (excludes digital and analog module power requirements) *
Ethernet Network Interface: Type Connector Rate Supported Protocols Maximum Segment Length	IEEE 802.3 network, 10Base-T/100Base-TX RJ-45. Supports Auto MDI-X (crossover cable not needed). 10/100 Mbps, half or full duplex Optomux over Ethernet, Modbus/TCP, OptoMMP (Opto 22's IEEE 1394-based memory-mapped protocol) 100 m (328 ft.) with Category 5 or superior UTP
Serial Network Interface: Type Connector Data Rates Supported Protocols Network Range	RS-422/485 serial link E1: Terminal block; E2: Terminal block (on mounting rack) 300, 600, 1200, 2400, 4800, 9600, 19200, and 38400 baud Optomux Up to 32 Optomux stations configured for multidrop can be used on a serial network of up to 1524 m (5000 ft.) total length. Up to 256 Optomux stations and longer line lengths can be used by installing network repeaters. Up to 256 Optomux stations configured for repeat mode can exist on a network.
Optomux I/O Functions	Digital I/O (E1): Read Point, Write Point, Latch Point (On/Off), Count, Pulse Duration, Time Delay, Pulse Generation, Watchdog Timer Analog I/O (E2): Read Point, Write Point, Input Averaging, Min/Max Recording (peak and valley), High/Low Range Testing, Offset and Gain Calculation, Waveform Generation, Watchdog Timer
Modbus/TCP, OptoMMP, and OPC I/O Functions	With these protocols, the following brain-based features are not available: ¢ No pulsing or time delay (E1) ¢ No pulse measurement ¢ No input averaging or waveform generation (E2)
LED Indicators	Status, Link, Activity, Full duplex, Transmit (serial), Receive (serial)
Jumper-selectable Serial Options	Group A: Multidrop or repeat mode, RS-485 termination and biasing Group B: Serial address (0 to 255), baud rate, 2- or 4-pass protocol
Operating Temperature	0 °C to 70 °C
Storage Temperature	- 40 °C to 85 °C
Humidity	0 - 95% humidity, non-condensing
Agency Approvals	DFARS
Warranty	30 months
* ±15 VDC ±0.25 V is required for the analog modules. Current depends on the number and types of modules installed. A 24 VDC power supply is required for analog modules that need a current loop source.

Write a Review